Plumber's Essentials: What You Need for Bathtub Installation
Plumber's Essentials: What You Need for Bathtub Installation
Blog Article
Do you find yourself on the lookout for answers about A Step-by-Step Guide to Installing a Bathtub?
Setting up a bath tub isn't precisely rocket science, yet it does need strong plumbing, woodworking, and in some cases, tiling abilities. Replacing an old bath tub with a new one is additionally a reasonably hard task. If the old bathtub is easily available, the project can relocate speedily; if you have to open up a wall surface to eliminate the old tub and place the new bathtub, the task is a lot harder. In either situation, the project is within a home handyman's skills, although you will require a helper to vacate the old bathtub as well as set in the brand-new one. Ensure you have actually certified on your own for the work as well as are comfortable attempting it. Rather than employing a professional to take over a halfway-completed job, it is far better to think about employing one prior to you begin. Possibilities are you might need a professional plumber to make tube links.
This article will help you mount a new bathtub in your washroom if you have actually currently gotten a brand-new tub and also don't require to change the arrangement of your previous water pipes.
Your devices and product checklist should consist of the following:
Removing Old Touches
If you require to change old faucets with new ones as a part of your setup, after that the first thing you ought to do is detach the water supply. After doing so, turn on the taps to drain pipes any type of water continuing to be in the system. The procedure of eliminating the existing taps can be rather troublesome due to the restricted access that is usually the instance.
Use a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that attaches the supply pipes to the faucets. Have a towel prepared for the remaining water that will certainly come from the pipelines. When the supply pipes have been eliminated, make use of the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will need to quit the single taps from transforming throughout this procedure. As soon as the faucets have been gotten rid of, the holes in the bath/basin will certainly have to be cleaned of any old sealing compound.
Before proceeding to fit the new taps, contrast the pipeline connections on the old taps to the brand-new faucets. If the old faucets are longer than the brand-new faucets, then a shank adapter is needed for the new faucets to fit.
Suitable New Touches
If the tails of the new taps are plastic, then you will require a plastic adapter to prevent damages to the thread. One end of the connector fits on the plastic tail of the tap and also the various other end provides a link to the existing supply pipes.
If you need to fit a monobloc, then you will certainly call for minimizing couplers, which links the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next, position the faucet in the installing opening in the bath/basin making sure that the washers are in location in between the tap as well as the sink. Protect the faucet in place with the maker given backnut. Once the tap is safely in place, the supply pipes can be linked to the tails of the faucets. The taps can either be connected by utilizing corrugated copper piping or with typical faucet connectors. The previous type ought to be attached to the faucet finishes first, tightening up just by hand. The supply pipelines can later on be attached to the various other end. Tighten up both ends with a spanner after both ends have been attached.
Setting up the Bath tub
Making use of both wood boards under its feet, position the bath tub in the required setting. The wooden boards are valuable in equally spreading the weight of the bath tub over the location of the boards as opposed to concentrating all the weight onto 4 tiny factors.
The following goal is to make sure that the bathtub is leveled all round. This can be attained by inspecting the spirit level and also changing the feet on the tub until the spirit level reviews degree.
To mount faucets, fit all-time low of the outermost adaptable tap port to the proper supply pipeline by making a compression join; then do the same for the other tap.
Turn on the water supply and inspect all joints and also brand-new pipework for leakages as well as tighten them if essential. Load the bath tub and likewise check the overflow electrical outlet and also the typical electrical outlet for leakages.
Lastly, repair the bath paneling as described in the maker's instruction manual. Tiling and also securing around the bathtub should wait till the bathtub has actually been utilized a minimum of once as this will settle it right into its final setting.
Preparing for the Installation
First of all, the sustaining framework supplied with the bath should be fitted (if called for) according to the manufacturer's guidelines. Next, fit the faucets or mixer to the bathtub. When suitable the tap block, it is important to make sure that if the faucet includes a plastic washer, it is fitted between the bathroom as well as the taps. On a plastic bath, it is likewise sensible to fit a sustaining plate under the taps unit to stop strain on the tub.
Fit the versatile faucet adapters to the bottom of the two taps utilizing 2 nuts and also olives (in some cases supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the outlet through the hole in the bathroom. Use the nut supplied by the supplier to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Ensure you use all of the provided washing machines.
Attach the catch to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bath must now prepare to be fitted in its last placement.
Tiling Around the Tub
In the location where the bathroom meets the tile, it is needed to secure the joins with a silicone rubber caulking. This is very important as the fitting can relocate sufficient to break a rigid seal, triggering the water to permeate the wall between the bathroom as well as the tiling, bring about problems with dampness and feasible leakages to the ceiling listed below.
You can pick from a variety of coloured sealers to blend in your components as well as fittings. They are marketed in tubes and also cartridges, and also can securing voids approximately a size of 3mm (1/8 inch). If you have a larger gap to fill, you can load it with spins of soaked newspaper or soft rope. Bear in mind to constantly fill up the bathtub with water prior to sealing, to permit the motion experienced when the tub remains in usage. The sealant can break relatively early if you do not consider this movement before securing.
Additionally, ceramic coving or quadrant ceramic tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are additionally quickly offered on the marketplace. It is a good idea to fit the ceramic tiles making use of water-resistant or water-proof adhesive and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Hopefully you liked our excerpt on How to Install a Bathtub. Thank you so much for taking a few minutes to browse our piece. If you please take a moment to share this blog entry if you liked it. Many thanks for your time. Please come by our website back soon.
Booking Page Report this page